Table 3-1. Special Tools and Equipment for Direct and General Support Maintenance

Table 3-1. Special Tools and Equipment for Direct and General Support Maintenance

Use reference

Ref

Identifying

Use

numbers

Par.

Figure

Fig.

Item

To hold intermediate clutch back

5-6

5-30

4910-572-8701

BOLT (2)

3-1

plate in position during buildup

5-105

5-58

8 3 5 6 1 8 6 (19207)

5-108

5-58

and disassembly.

4910-572-8699

3-1

BOLT, puller (3)

5-32

5-6

To remove ground sleeve diaphragm

8 3 5 6 2 0 0 (19207)

assembly.

5-109

5-58

4910-572-8643

3-1

COMPRESSOR

5-36

To compress and hold low, reverse,

5-6

8 3 5 6 1 8 7 (19207)

5-44

and intermediate clutch package

5-6

5-95

5-58

during installation and removal,

5-102

5-58

and compress reverse clutch pack

to remove or install holding pins.

4910-673-3801

3-1

EYE, lifting

To lift high-range clutch package and

5-20

5-6

10865773(19207)

converter drive cover; used with

5-34

5-6

strap 4910-572-8608.

5-58

5-106

5-120

5-58

3-1

G U I D E BOLT SET

5-65

To position front and rear oil pumps,

5-16

5-88

and front and rear pitot tubes and

5-58

5-91

5-58

diaphragm.

5-108

5-58

5-111

5-58

5120-316-9182

To install front oil pump seal, install

5-57

5-11

3-1

HANDLE

7 9 5 0 8 6 4 (19207)

high clutch housing bushing, install

5-64

5-16

output bearing and seal, install

5-69

5-21

5-79

converter drive cover bushing and

5-41

output shaft bushing; used with

5-85

5-58

replacers 5 1 2 0 - 5 7 2 - 8 6 6 0 , 5120-

5-87

5-58

.572 -8658, 5120-572-8615, 5120-

a n d 5120-759-5415.

572-8656,

4010-572-8688

To hold stator freewheel rollers and

5-60

5-11

3-1

H O L D E R ASSEMBLY

springs in place to assemble race.

8356195 (19207)

4910-572-8612

3-2

To check transmission oil pressures.

5-143

5-62

KIT, pressure gage

8 3 5 6 1 7 6 (19207)

5-44

5-62

5180-572-8607

5-68

5-18

To install and remove clutch piston

3-1

KIT, remover and replacer

8 3 5 6 1 7 0 (19207)

5-70

5-21

return spring retaining ring.

5-71

5-21

To install turbine shaft snap rings.

3120-572-8663

5-73

5-21

3-1

KIT, snap ring

8 3 5 6 1 9 1 (19207)

5-117

5-58

5-118

5-58

5120-572-8712

To remove output seal.

5-17

5-6

3-1

PULLER

ASSEMBLY

8 3 5 6 2 0 1 (19207)

To install front oil pump seal: used

5120-572-8660

5-64

5-16

3-1

REPLACER

with handle .5120 -316-9182.

8 3 5 6 1 7 3 (19207)

5-21

To install high clutch housing

5-69

5120-572-8658

3-1

REPLACER

bushing: used with handle 5120-

310-9182.

TO install output bearing and oil seal;

5-85

5-58

3-1

REPLACER

used with handle ,5120-316-9182.

T o install converter drive cover

5-57

5-11

3-1

REPLACER

bushing: used with handle .5120 -

316-9182.

5-79

5-41

To install output shaft bushing: used

5120-759-5415

3-1

REPLACER

with handle .5120 -316-9182.

8 3 5 6 2 0 4 (19207)

5-1

5-6

3-1

4910-572-8614

To lift transmission and to mount

SLING

5-58

5-140

8 3 5 6 1 8 4 (19207)

transmission in stand.

5-2

5-6

3-3

To hold and position transmission for

STAND

4010-499-4196

5-3

5-6

teardown and build up.

5-140

5-58

T O remove or install converter drive

5-20

5-6

3-1

STRAP, lifting

cover. and check mounting space;

5-120

5-58

u s e d with lifting eye 4910-673-

3801.

3-3