Fuse setters.

TM 746-10

(6) Component packing.

Place all items

comprising the fire direction set in a wood or plywood

m. Heating and tie-down unit (truck-mounted).

box. Block the contents with wood blocking (see figure

(1) Process unit in a driveaway condition.

4-2).

Preserve all unpainted surfaces with P-1. Seal door

j. Fuse setters.

seams of the fin box with tape. Fold tie-down strap

assemblies of saddle assemblies and secure in place

(1) Fuse setters with cases. Place fuse in

with plastic tape. Secure wheel and tire assembly in its

case, close lid, and secure with fasteners. Place a

place on the cargo truck.

quantity of fuse setters in a fiberboard box and close

with tape.

(2) Put electrical caps in place and draw

down finger tight.

(2) Fuse setters without cases. Wrap one

fuse setter in cellulosic cushioning and secure with tape.

(3) Process vehicle chassis per the applicable

Place fuse setter in a fiberboard box. Secure with tape.

paragraphs of this manual.

Place a quantity of fuse setters in a fiberboard box and

(4) Package electric blanket sections per the

secure with tape.

general provisions of paragraph 4-102.

k. Guns. In addition to process C-3, clean with

n. Hoisting unit. Preserve noncritical, unpainted

rifle bore cleaner followed by a solvent wash. Insert a

metal surfaces with P-1. Preserve roller chains, gears,

VCI bore tube into the barrel bore. Extend VCI bore

and machined surfaces with P-ll.

Wrap all P-ll

tube 1 inch from the end of the barrel bore and bend.

preserved surfaces with greaseproof barrier material

Wrap each weapon entirely with VCI and mold to

and secure with tape. Process tools per the appropriate

configuration of the item. Unit pack wrapped weapon

provisions of paragraph 4-2.

Place processed

submethod IC-1.

components and repair parts in a fiberboard box,

(1) Guns under 40 pounds.

Place one

cushion with cellulosic cushioning, and secure with tape.

weapon in a fiberboard box, cushion with cellulosic

(1) Hoists weighing up to 1,000 pounds.

cushioning or bound fiber, and secure with plastic tape.

Pack one complete hoist with consolidated processed

Reinforce fiberboard box by applying filament reinforced

repair parts, tools, and publications in a wood or

tape around the circumference of the box.

plywood box (see figure 4-2). Use wood blocking and

(2) Guns 40 pounds and over. Place one

bracing to immobilize the contents. Securely nail all

weapon in a double-wall fiberboard or wood box, block

blocking.

and brace the weapon per blocking (fig 4-2), and secure

(2) Hoists weighing 1,000 pounds and over.

with tape (fig 4-3). Reinforce fiberboard box by applying

Pack one complete hoist with consolidated processed

filament reinforced tape around the circumference of the

repair parts, tools, and publications in an open wood

box.

crate (fig 4-1). Shroud hoist with waterproof barrier and

l. Towed (Vulcan).

secure with plastic tape. Block and brace as specified in

(1) above.

(1) General requirements. Prepare weapon

for shipment in a towed condition. Apply general

o. Indicator, connecting rod alignment. Preserve

requirements specified in paragraph 4-102f except

unpainted surfaces with P-7, wrap preserved surfaces

remove radar antenna unit from the weapon and

with greaseproof barrier material, and secure with tape.

package as specified herein. Clean, dry, preserve, and

Place all components of the indicator in carrying case.

pack gun and its components as specified in f above.

Place cellulosic cushioning inside case to prevent

movement. Close carrying case cover and secure with

(2) Radar antenna unit. Cover antenna cable

fasteners provided. Place carrying case in a fiberboard

connectors and waive guide sections of antenna with

box and secure with tape.

greaseproof barrier material and secure with tape.

Secure waive guide sections in place with tape. Unit

p. Jack, dolly-type, hydraulic. Preserve exterior,

pack antenna attaching hardware submethod IC-1 and

noncritical, unpainted surfaces with P-1 and exposed,

attach bag to antenna unit with tape.

critical, ferrous metal surfaces with P-11. Wrap all

surfaces preserved with P-ll with greaseproof barrier

material and secure in place with tape. Clean accessory

CAUTION

tools and preserve, as specified herein, and pack in a

fiberboard box. Seal box with tape and secure to the

Waive guide bends easily. Place the radar antenna

basic unit with

unit in a fiberboard box and completely encapsulate

the item in polyurethane foam with a minimum 2-

inch thickness. Secure box with tape. Place box in

the carriage directly in front of the generator and

secure to the carriage with filament reinforced tape.

4-33