Quantcast Repair of Stand Assembly.

 

Click here to make tpub.com your Home Page

Page Title: Repair of Stand Assembly.
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 3-2. Slider Assembly (Typical)
Up
TM-9-4931-583-30-P Boresight Kit T-102300-101 (
Next
Repair of Boresight Assembly Miscellaneous  Components.
TM
9-4931-583-30&P
n. Dent Repair.
(n) Install washer (28) and washer (27) over
each stud with washer (28) against frame.
(1) Using scouring pads, remove paint from
dent and surrounding area.
(o) Install one nut (26) on each stud and
tighten until snug. Install second nut (26) to secure first
(2) Replace part if cracked.
nut.
(p) Ensure that slide tapes on each side of
(3) If dented only, paint cleaned area with
polyamide epoxy primer.
frame and fixed frame are in contact with each
other.
b. Disassembly.
(q) Ensure that bracket (19) screws are
loose enough to allow bracket to move.
(1) Remove knob (28, figure C-11) from each
side of vertical support assembly (20).
(r) Position plate (18) against mounting
point on fixed frame with tape on plate facing tape
(2) Remove five quick release pins (2) from
on bracket (19). Fasten plate with two screws (15)
chains (6).
and washers (17).
(3) Remove four nuts (10), washers (11),
(s) Install second plate using steps (q) and (r)
washers (12), and bolts (13) from each rigid caster (14)
above.
and remove casters from base assembly (16).
NOTE
(4) Remove four nuts (10), washers (12),
washers (11), and bolts (13) from each swivel caster (15)
I f bracket is forced against plate,
and remove casters from base assembly (16).
movement of frame will be erratic during
alignment. Bracket must touch plate
with no force applied.
c. Inspection.
Replacement is required if
discrepancy causes part to be unserviceable, or
tmresight assembly to be twisted out of alignment
(t) Position both brackets (19) until the
when installed on stand.
taped surfaces are flush with and parallel to the
taped surfaces of both plates (18) with surfaces in
(1) Warped or bent.
contact with each other.
(2) Damage.
(u) Tighten the three mounting screws
(16) on each bracket (19).
(3) Loose or missing parts.
(v) Assemble boresight  assembly per
(4) Threaded items for thread damage.
i n s t r u c t i o n s in paragraph 2-3  and perform
alignment per paragraph 2-4.
(5) Wheels for serviceability, smooth
operation and brakes for condition.
Repair of Stand Assembly.
(6) Quick release pins for condition.
Expendable Supplies and Materials List
Part No./
d. Assembly.
Nomenclature
Specification
(1) Attach swivel casters (15) to base assembly
(16) using four bolts (13) with washers (11) under bolt
Pads, Scouring
L-P-50,
heads and nuts (10), with washers (12) under nuts.
Type I, Class 1
P o l y a m i d e Epoxy Primer
MIL-P-23377,
Class 2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business