 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 9-6685-202-14
(19) Do not remove exhaust ring (27) or intake
27. Washer, steel WSC 41-1285
ring (25) from center plate (17) unless replacement of
28. Filter, air WSC 41-0890
rings or center plate is necessary. Examine intake and
29. Gasket, WSC 41-0383
exhaust rings and clean thoroughly while still assembled
30. Chamber, intake WSC 41-1048
to center plate.
31. Nipple, WSC 41-0920
(20) Replace the pump motor if inspection
32. Screw, hex head, WSC 2-01-0520, steel, 3/8-
shows that it does not operate properly.
16 x 1 1/4
33. Plate, back WSC 41-1055
KEY to fig. 4-10
34. Shaft, end WSC 41-1255
35. Screw, fillister head, WSC 2-00-2708, steel, 10-
1. Setscrew, pulley 5/16-18 x 1/2 WSC 2-01-6308
32 x 1/2
2. Pulley, WSC 41-2191
36. Nut, hex, WSC 2-31-2521, steel, 3/8 x 16
3. Seal, oil WSC 1401E
37. Ring, outer WSC 41-2563
4. Gasket, seal WSC 41-0643
38. Rotor WSC 41-1041
5. Key, WSC 41-0624
39. Holder, spring WSC 41-1063
6. Shaft and retaining ring WSC 41-1060
40. Spring, WSC 41-1304
7. Ring, retaining WSC 41-1150
41. Vane, WSC 41-1059
8. Key, woodruff, WSC 41-0613
42. Screw, socket head, WSC 2-01-6112, steel, 1/4-
9. Screw, fillister head WSC 2-00-2705, steel 10-
20 x 3/4
32 x 5/16
43. Ring, inner, WSC 41-1042
10. Legs, WSC 41-1049
44. Gasket, WSC 41-0056
11. Washer, rubber WSC 41-1267
45. Seal, WSC 41-0578
12. Disc, glass WSC 41-1268
46. Cover, oil cover, WSC 41-1061
13. Washer, tension WSC 41-1266
47. Screw, fillister head, WSC 2-10-2608, steel, 8-
14. Case, oil WSC 41-1047
32 x 1/2
15. Cap, dust WSC 41-1345
48. Screwstick, self-tapping, 1-72 x 1/8, WSC 2-09-
16. Gasket WSC 41-1052
1202
17. Screw, hex head WSC 2-01-0332, steel 5/16-18
49. Plate, pump instruction, WSC 41-1936
x2
50. Cap, oil drain, WSC 41-1166
18. Washer WSC 41-2363
51. Disc, WSC 41-1192
19. Plate, front WSC 41-1045
52. Fitting, brass WSC 41-1168
20. Rotor, WSC 41-1400
53. Screw, round head, WSC 2-01-5308, steel,
21. Valve, spring WSC 41-1239
5/16-18 x 1/2
22. Washer, brass, No. 10, WSC 2-71-0040
23. Screw, fillister head WSC 2-00-2705, steel, 10-
NOTE
32 x 5/16
The key numbers shown below in
24. Washer WSC 41-1056
parenthesis refer to figure 4-10.
25. Plug, WSC 41-1039
26. Plate, center WSC 41-1044
4-24
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals