SECTION I. INTRODUCTION - TM-9-3830-206-34P0005

SECTION I

INTRODUCTION

Explanation

Code

1. Scope

This manual lists repair parts required for the

Repair Parts, Special Tools and Test Equipment

which are not procured or stocked, as such, in the

performance of direct support, general support and

supply system but are to be manufactured at

depot maintenance of the Winch Assemblies, FSN

indicated maintenance levels.

2 5 2 0 - 0 4 0 - 2 1 1 2 , 2590-402-5200 and 2590-753-

Assemblies which are not procured or stocked as

8687.

such, but are made up of two or more units. Such

2. General

component units carry individual stock numbers

a n d descriptions, are procured and stocked

This Repair Parts List is divided into the following

separately and can be assembled to form the

sections:

r e q u i r e d assembly at indicated maintenance

a. Repair Parts--Section II. A list of repair

categories.

parts

a u t h o r i z e d for the

p e r f o r m a n c e of

Parts and assemblies that are not procured or

maintenance at the direct support, general support

stocked because the failure rate is normally below

that of the applicable end item of component. The

and depot level in figure and item number

failure of such part or assembly should result in

sequence.

retirement of the end item from the supply system.

b. Special

Tools,

Test

and

Support

Repair Parts which are not procured or stocked.

Equipment. Not Applicable.

The requirement for such items will be filled by

c. F e d e r a l S t o c k N u m b e r a n d R e f e r e n c e

the next higher assembly or component.

N u m b e r Index--Section III. A list of Federal

Repair Parts, Special Tools, and Test Equipment

stock numbers in ascending numerical sequence

which are not stocked and have no foreseen

followed by a list of reference numbers in ascending

mortality. The indicated maintenance category

requiring such repair parts will attempt to obtain

alpha-numeric sequence, cross-referenced to the

the parts through cannibalization or salvage, if not

illustration figure number and item number.

obtainable through cannibalization or salvage, the

3. Explanation of Columns

item may be requisitioned with exception data,

from the end item manager, for immediate use.

The following provides an explanation of columns

Major assemblies that are procured with PEMA

in the tabular lists in sections II, III, and IV.

funds for initial issue only as exchange assemblies

a. Source, Maintenance, and Recoverability

at DSU and GSU level. These assemblies will not

C o d e s (SMR), Column 1.

he stocked above the DS and GS level or returned

(1) Source Code, indicates the selection status

to depot supply level.

and source for the listed item. Source Codes are--

NOTE

Cannibalization or salvage may be used as

Code

Explanation

a source of supply for any items source

Repair Parts, Special Tools and Test Equipment

s u p p l i e d from GSA / DSA, or Army supply

coded above, except those coded X1.

s y s t e m , and authorized for use at indicated

(2) Maintenance Code, indicates the lowest

maintenance categories.

category of maintenance authorized to install the

Repair Parts, Special Tools and Test Equipment

listed item. The maintenance level codes are--

which are procured and stocked for insurance

purposes because the combat or military essen-

Code

Explanation

tiality of the end item dicates that a minimun

Crew of Operator Maintenance

quantity be available in the supply system.

Organization Maintenance

Assigned to items which are NSA design con-

Direct Support Maintenance

trolled: unique repair parts, special tools, test,

General Support Maintenance

measuring and diagnostic equipment, which are

stocked and supplied by the Army COMSEC

Depot Maintenance

Logistic System and which are not subject to the

(3) Recoverability Code, indicates whether

provisions of AR 380-41.

unserviceable items should be returned for recovery

Assigned to items which are NSA design con-

P10

or salvage. Recoverability Codes are--

trolled: s p e c i a l tools, test, measuring and

diagnostic equipment for COMSEC

support,

Explanation

Code

which are accountable under the provisions of AR

Applied to repair parts, (assemblies and com-

380-41, and which are stocked and supplied by

ponents) special tools and test equipment which are

the Army COMSEC Logistic System.