|
|
TM 55-4920-325-14&P
j. Remove two pan head screws (30), two
a. Remove four screws (1) and detach shield
screws (31) and two Iockwashers (32) and detach
plate (2) from capacitance simulator assembly
two simulator brackets (33) from simulator chas-
(15) and simulator chassis (56).
sis (56).
b. Remove four screws (3), four hex nuts (4)
k. Remove pan head screw (34), hex nut
and four Iockwashers (5) and detach two shield
(35), flat washer (36) and lockwasher (37) and de-
brackets (6) from shield plate (2).
tach nylon clamp (38) from simulator chassis (56).
c. Remove two pan head screws (7), four in-
sulating washers (8) and two flat washers (9) and
l. Remove hex nut (39) and washer (40) and
detach bracket assembly (10) from capacitance
detach rotary switch S401 (41) from simulator
simulator assembly (15). Refer to paragraph 4-11
chassis (56).
to disassemble bracket assembly (10).
m. Remove hex nuts (42) and washers (43)
d. Remove five screws (11) and detach -sim-
and detach rotary switch S402 (44) from simulator
ulator shield (12) from capacitance simulator as-
chassis (56).
sembly (15) and simulator chassis (56).
n. Remove hex nut (45) and washer (46) and
Remove four screws (13) and four screws
detach rotary switch S403 (47) from simulator
(14). and detach capacitance simulator assembly
chassis (56).
(15) from two simulator brackets (33). Refer to
o. Remove 12 pan head screws (48) and 12
ulator assembly (15).
Iockwashers (49) and detach three solder lugs
(50) and three connectors J401 (51), J402 (52)
f. Remove three pan head screws (16), three
and J403 (53) from simulator chassis (56).
flat washers (17), and three Iockwashers (18) and
detach three nylon clamps (19 and 20) from sim-
p. Remove two hex nuts (54) and detach two
ulator brackets (33).
panel bushings (55) from simulator chassis (56).
g. Remove four pan head screws (21), four
4-10. Disassembly of Panel Assembly.
teflon bushings (22), four washers (23), and four
To disassemble the panel assembly, refer to
flat washers (24) and detach two capacitor assem-
blies C401 (25) and C402 (26) from two simulator
brackets (33).
NOTE
h. Remove two retaining rings (27) and ex-
As disassembly proceeds, tag and dis-
tract two shouldered shafts (28) from two panel
connect wiring as required.
bushings (55).
i. Remove four O-ring seals (29) from two
shouldered shafts (28).
KEY to fig. 4-12:
21.
1.
Self-locking nut
11.
Connector gasket
22.
2.
Knob
Nylon washer
12.
Hex nut
23.
Resistor R114
Terminal E101
3.
13.
Washer
24.
Resistor R111
4.
Screw
Washer
14.
Nylon washer
5.
Indicator light and lens
15.
25.
Resistor R112
5a.
Self-locking nut
assembly DS101
26.
Resistor R113.
6.
Cap and chain
16.
Washer
27.
Hex nut
7.
O-ring screw
Toggle switch boot
17.
28.
Rotary switch S104
Hex nut
8.
Hex nut
18.
29.
Resistor R105
9.
Lockwasher
Toggle switch S101
19.
30.
Hex nut
10.
Connector J104
20.
Hex nut
4-17
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |