Quantcast Chapter 1. INTRODUCTION - TM-9-4931-583-30-P0009

 

Click here to make tpub.com your Home Page

Page Title: Chapter 1. INTRODUCTION
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Up
TM-9-4931-583-30-P Boresight Kit T-102300-101 (
Next
Figure 1-1. Boresight Assembly, Ground Support Equipment (BAGSE)
TM 9-4931-583-30&P
INTRODUCTION
SECTION I. GENERAL
1-5. Reporting Equipment Improvement Recom-
1-1. Scope. This manual is for your use in operating
mendations (EIR).  EIR can and must be sub-
and maintaining the Boresight Assembly Ground Sup-
mitted by anyone who is aware of an unsatis-
port Equipment, T-102300-107.
factory condition with the equipment design or
use. It is not necessary to show a new design or
list a better way to perform a procedure, just
1 - 2 .  M a i n t e n a n c e Forms and Records.
simply tell why the design is unfavorable or why a
Maintenance forms and records are listed in
procedure, is difficult. EIR's will be prepared on
DA PAM 738-750.
SF 368, Quality Deficiency Report. Instructions
for preparing EIR's are provided in DA PAM
738-750, The Army Maintenance Management
1-3. Destruction of Army Materiel to Prevent
System. EIR's should be mailed directly to Com-
Refer to TM 750-244-1-5 for
Enemy Use.
m a n d e r , US Army Armament, Munitions and
instructions pertaining to destruction of Army
Chemical Command, ATTN: AMSMC-QAD, Rock
materiel to prevent enemy use.
A reply will be
Island, Illinois, 61299-6000.
furnished directly to you.
1 - 4 .  Q u a l i t y Assurance/Quality Control.
This information not available at this time.
DESCRIPTION AND TABULATED DATA
SECTION II.
1-6. Description.
1-7. Tabulated Data.
a. The boresight kit consists of the disassembled
a. Physical.
Boresight Assembly Ground Support Equipment
( 1 ) Boresight Assembly (Assembled).
(BAGSE) packed in seven carrying cases.
b. The BAGSE is a compact portable unit used to
provide the proper angles for boresighting the arma-
(a) Length - 84.75 inches.
ment subsystems of the helicopter.
(b) Width - 48.75 inches.
c. The BAGSE (figure 1-1) consists of a
(c) Height - 54 inches.
boresight assembly, stand assembly and separate
align blocks. The boresight assembly is a series
(2)  Cases,  Boresight  Assembly
of tubes and blocks which, when assembled,
(Disassembled and Packed). (Figure 1-2.)
positions alignment block holes for boresighting
each armament subsystem. The stand assembly
CASE
CUBIC
WEIGHT/
is a four wheeled support rack for the boresight
NO.
FEET
POUNDS
assembly. Separate alignment device assemblies are
installed in each armament subsystem.
22.1
1
143
22.1
2
147
d. All components required to boresight the
22.2
3
150
helicopter, including boresight telescopes and
17.9
4
105
gunner quadrants, except electrical power source,
5.2
5
53
are included in the assembly cases.
5.2
6
59
12.2
7
106
e. The BAGSE is packaged and transported
b. Power Requirements. 28 vdc
is used to
in cases (figure 1-2).
operate three illumination assemblies
lamps.
Change 1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business