Special Information - TM-9-2805-203-34P0007

in the functional group. A V appearing in this

(1) First.

Using

the

table

contents,

column in lieu of a quantity indicates that a definite

determine the functional subgroup within which

quantity cannot be indicated (e.g., shims, spacers;

the repair part belongs (e.g., engine, engine

etc).

a s s e m b l y ; and clutch, c l u t c h assembly). This is

f . 30-Day DS/GS Maintenance Authorization,

necessary since i l l u s t r a t i o n s a r e p r e p a r e d f o r

Columns (6) and (7).

functional subgroups and listings are divided into

(1) The repair parts list includes asterisk

the same groups.

entries in separate columns-one for direct support

(2) Second. Find the illustration covering the

( D S ) and one for general support (GS)-as ap-

functional subgroup to which the repair part

propriate to indicate the total range of repair parts

belongs.

authorized for use at that category or required to be

(3) T h i r d . Identify the repair part on the

removed or disassembled during the performance

illustration and note the illustration figure and item

of authorized maintenance operations. They will be

number of the repair part.

requisition.ed initially on an as-required basis. The

(4) Fourth. Using the repair parts listing, find

repair part authorized at the Direct Sup-

the functional subgroup to which the repair part

port/General

Support

levels

will

those

belongs and locate the illustration figure and item

authorized for the maintenance mission at these

number noted on the illustration.

levels. Requirements for repair parts stockage and

b. When the Federal stock number or reference

for distribution to support units will be based on

n u m b e r is known:

d e m a n d and determined in accordance with AR

(1) First. Using the index of Federal stock

710-2.

numbers and reference numbers, find the pertinent

(2) Special tools or test, measurement, and

Federal stock number or reference number. This

diagnostic equipment (TMDE) and other support

index is in ascending alphameric sequence cross-

-referenced to the illustration figure number and

e q u i p m e n t peculiar to an item are listed with

item number.

the

appropriate

density

quantities

spread / allowance columns.

(2) Second. Using the repair parts listings,

find the functional subgroup of the repair part and

g. 1 - Y e a r

Allowances per 100 Equip-

the illustration figure number and item number

ments / Contingency Planning Purposed, Column

referenced in the index of Federal stock numbers

(8). This column indicates the requirement for

and reference numbers.

c o n t i n g e n c y planning purposed. An asterisk in-

dicates authorization to obtain or use as required.

h. Depot Maintenance Allowances per 100

Equipments, Column (9). This column indicates

authorization for depot use.

i. Illustrations, Column (10). This column is

divided as follows:

(1) F i g u r e N u m b e r , S u b c o l u m n (a). T h i s

column indicates t h e f i g u r e n u m b e r o f t h e

illustration in which the item is shown.

(2) I t e m N u m b e r , S u b c o l u m n ( b ) . T h i s

column indicates the callout number used to

reference the item in the illustration.

4. Special Information

a. The basis of issue for authorized special tools,

test, and support equipment is the number of end

items of equipment supported and the number of

personnel allocated to perform the required

maintenance operations (such as, one soldering iron

p e r five MOS284.1 supporting 1-15 radio sets

AN/ARC-51).

b. Parts which require manufacture or assembly

at a category higher than that authorized for in-

s t a l l a t i o n will indicate in the SMR column the

higher category.

T h e reporting of errors, omissions, and recom-

5. How to Locate Repair Parts

mendations for improving this publication by the

a. When the Federal stock number or reference

indivdual user is encouraged. Reports should be

n u m b e r is unknown: