 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 55-1740-201-23P
they will be evacuated to a depot for
dicated maintenance category requir-
evaluation and analysis before final
ing such repair parts will attempt to
disposition.
obtain the parts through cannibaliza-
Higher dollar value recoverable re-
T
tion or salvage. The item may be
p a i r parts, special tools and test
requisitioned with exception data,
equipment which are subject to special
f r o m the end item manager, for
handling and are issued on an ex-
immediate use.
change basis. Such items will be
G
Major assemblies that are procured
repaired or overhauled at depot main-
with PEMA funds for initial issue only
t e n a n c e activities only. No repair
as exchange assemblies at DSU and
may be accomplished at lower levels.
GSU level. These assemblies will not
U
Repair Parts, Special Tools and Test
be stocked above the DS and GS level
Equipment specifically selected for
or returned to depot supply level.
salvage by reclamation units because
Note: Cannibalization or salvage may be
of precious metal content, critical
used as a source of supply for any items
materiels, high dollar value or re-
source coded above except those coded X1
and aircraft support items as restricted
usable casings or castings.
by AR 700-42.
b. Federal Stock Number. Indicates the
(2) Maintenance code, indicates the
federal stock number assigned to the item
lowest category of maintenance
and will be used for requisitioning pur-
a u t h o r i z e d to install the listed
poses. Items source coded A, M, X1, or
item. Maintenance level codes are:
X2 are not assigned a federal stock number.
c. Description. Indicates the federal
item name and any additional description
of the item required. The description col-
umn contains the following subcolumns.
(1) Reference Number and Manufact-
(3) Recoverability code, indicates
urer's Code. Indicates a part num-
w h e t h e r u n s e r v i c e a b l e items
b e r or other reference number
should be returned for recovery
for the listed item followed by the
or salvage. Items not coded are
applicable five-digit federal supply
nonrecoverable.
Recoverability
code for manufacturers, in paren-
codes are:
thesis.
(2) Usable on Code
R
Applied to repair parts, (assemblies
and components) special tools and
test equipment which are considered
economically reparable at direct and
general support maintenance levels.
d. Unit of Measure (U/M). A two-char-
When the item is no longer econo-
acter alphabetical abbreviation indicating
m i c a l l y reparable, it is normally
the amount or quantity of the item upon
disposed of at the GS level. When sup-
which the allowances are based e.g., ft,
ply considerations dictate, some of
ea, pr.
these repair parts may be listed for
automatic return to supply for depot
e. Quantity Incorporated in Unit. Indi-
cates the quantity of the item used in the
level repair as set forth in AR710-50.
assembly. A "V" appearing in this column
When so listed, they will be replaced
instead of a quantity indicates that a definite
by supply on an exchange basis.
quantity cannot be shown.
S
R e p a i r Parts, Special Tools, Test
f. Fifteen-Day Organizational Mainten-
Equipment and assemblies which are
ance Allowances.
economically reparable at DSU and
(1) The allowance column is divided
GSU activities and which normally
into four subcolumns. Indicated in
are furnished by supply on an exchange
each subcolumn opposite the first
basis. When items are determined by a
appearance of each item is the
GSU to be uneconomically reparable,
iv
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals