Quantcast Repair of Alignment Mounting Frame Assembly

 

Click here to make tpub.com your Home Page

Page Title: Repair of Alignment Mounting Frame Assembly
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Repair of Upper Frame Assembly
Up
TM-9-4931-583-30-P Boresight Kit T-102300-101 (
Next
Figure 3-2. Slider Assembly (Typical)
TM 9-4931-583-30&P
NOTE
Remove four screws (15) and washers (17) from slider
and remove slider. Identify location of shims, if any,
The slider assemblies must be protected
that are installed between slider and bracket. Retain
from environmental elements such as
shims for reinstallation.
dust and dirt when not in use.
(e) Remove three screws (16) and washers
The lubrication task is for corrosion
(17) and remove bracket (19) from each side of frame.
prevention only.  Conduct this task
monthly when BAGSE is used in areas
of high atmospheric humidity.
(f) Remove one bolt (24) and nut (20) from
bracket (25) and remove from each side of frame.
(a) Remove any protective covering that
may be over the slider.
(b) Spray between top plate (3, figure 3-2)
NOTE
and bottom plate (4) with corrosion preventive com-
pound, WD 40 MIL-C-23411. Wipe away any excess
Shims may be installed between slider
lubricant.
and frame. Carefully remove slider so as
to retain location identification of any
(c) Rotate slide adjustment knob (5) in
shims that may be installed.
each direction to check freedom of motion and
spread compound. Return slider to midposition.
(g) Loosen four bolts (29) and remove slider
(d) Wrap slider with barrier material or
assembly (21) from fixed frame (42), allowing bolts to
equivalent protective wrapping and secure with tape,
remain to hold any shims that may be installed.
unless mounting slider assembly on boresight assem-
Remove any shims from bolts, retaining location iden-
bly.
tity. Remove bolts (29) and washers (30).
(6) Assemble mounting frame assembly.
Refer to figure C-8 for breakdown and parts
(h) Loosen four bolts (29) and remove slider
identification numbers.
assembly (36) from fixed frame (42), allowing bolts to
remain to hold any shims that may be installed.
NOTE
Remove any shims from bolts, retaining location iden-
tity. Remove bolts (29) and washers (30).
If slider studs do not align with holes in
frame (39, figure C-8) slider shall be
repositioned, using shims between slider
(4) Inspect each part. Any discrepancy,
and mounting.
except cleanliness, is cause for replacement.
(a)
Warped or bent.
(a) Position slider assembly (31) to right
corner of fixed frame (42), installing any shims removed
(b)
Damage.
in same location. Fasten slider and shims with four
bolts (29) and washers (30).
(c)
Loose or missing parts.
(b) Position slider assembly (31) to left corner
(d)
Threaded items for thread damage.
of fixed frame (42), installing any shims removed in
same location. Fasten slider and shims with four bolts
(e)
Sliders for binding, corroded or worn.
(29) and washers (30).
(f) Cleanliness. Clean, if required, per
(c) Insert one clamp (14) through hole in
lower end on each side of fixed frame from rear to front.
Install washer (13) and knob (12) on each of the two
(5) Corrosion control of slider assembly.
clamps.
3-5

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business