Reassembly of Panel Assembly.

TM 55-4920-325-14&P

i. Connect and solder resistor R118 (1)

l . Mount two caps (34) on two potenti-

across teflon terminal (22) and transformer T101

ometers R106 (38) and R107 (39).

(6) using solder (item 4, table 1-4).

m. Solder capacitors

C110 (55) and C111 (56)

k. Check that components and wires are

across appropriate pins

of rotary switch S103 (33)

connected to proper terminals and remove tags.

and solder lugs (54) in

accordance with tags, us-

ing solder (item 4, table

1-4).

4-19. Reassembly of Panel Assembly.

n. Attach rotary switch S103 (33) to panel

To reassemble the panel assembly, refer to fig-

(75) using hex nut (32).

ure 4-12 and proceed as follows:

o. Attach rotary switch S102 (31) to panel

NOTE

(75) using hex nut (30).

As reassembly proceeds, reconnect

w i r i n g in accordance with tags on

p. Solder resistor R105 (29) across appropri-

wires, using solder (item 4, table 1-4).

ate pins of S102 (31) in accordance with tags, us-

a. Attach two handles (73) and ground strap

ing solder (item 4, table 1-4).

(74) to panel (75) using four screws (71), four

Attach rotary switch S104 (28) to panel

Iockwashers (72) and locking compound (item 3,

(75) using hex nut (27).

table 1-4).

r. Solder four resistors R114 (23), R111 (24),

b. Attach two dial locks (70) to panel (75) us-

R112 (25) and R113 (26) across appropriate pins

ing two hex nuts (67), two Iockwashers (68) and

of rotary switch S104 (28) in accordance with

two nylon washers (69).

tags, using solder (item 4, table 1-4).

c. Attach two terminals E102 (64) and E103

s. Using a pliers, rotate shafts of rotary

(65) to panel (75) using two self-locking nuts (62),

switches S102 (31), S103 (33), and S104 (28) to

two washers (63) and two washers (66).

extreme counterclockwise position. Mount three

d. Attach three connectors J102 (59), J103

knobs (22) on rotary switch shafts, align marker

(60) and J105 (61) and three connector gaskets

with extreme left panel graduation, and tighten

(58) to panel (75) using ten O-ring screws (57)

setscrews of knobs (22).

and locking compound (item 3, table 1-4).

t. Attach two fuseholders (21) to panel (75)

e. Attach two solder lugs (54) to connector

using two hex nuts {20) and install two fuses (see

J 103 (60) using two O-ring screws (52), two hex

paragraph 3-12a).

nuts (53) and locking compound (item 3, table 1-

u. Attach toggle switch S101 (19) to panel

4).

(75) using hex nut (18) and toggle switch boot

f. Attach three caps and chains (48) to panel

(17).

(75) using two screws (49), two self-locking nuts

v. Attach indicator light and lens assembly

(50), four nylon washers (51) and locking com-

(15) to panel (75) using three washers (13, 14 and

pound (item 3, table 1-4).

16) and hex nut (12) and install lamp (see para-

Mount three caps (48) on connectors J102

graph 3-12b).

(59) J103 (60) and J105 (61).

w. Attach connector J104 (10) and connector

h. Attach two potentiometers R108 (46) and

gasket (11) to panel (75) using three O-ring

R109 (47) to panel (75) using two hex nuts (44)

screws (7), three hex nuts (8), three Iockwashers

and two internal tooth Iockwashers (45).

(9) and locking compound (item 3, table 1-4).

i. Attach two caps and chains (40) to panel

x. Mount cap and chain (6) on connector

(75) using screw (41), two nylon washers (42),

J104 (10); attach cap and chain (6) to panel (75)

self-locking nut (43) and locking compound (item

using screw (4), two nylon washers (5), self-lock-

3, table 1-3).

ing nut (5A) and locking compound (item 3, table

1-4).

j. Mount two caps (40) on two potenti-

ometers R108 (46) and R109 (47).

y. Attach terminal E101 (3) to panel (75) us-

ing self-locking nut (1) and nylon washer (2).

k. Attach two potentiometers R106 (38) and

R107 (39) to panel (75) using two hex nuts (35),

z. Check that components and wires are

two teflon bushings (36) and two washers (37).

connected to proper terminals and remove tags.

4-24